Showing results: 991 - 1005 of 1086 items found.
-
9355-1 -
Solar Electronics Company
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
CBH2 -
CAMI Research Inc. (CableEye®)
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
COF-02 -
Jinan Leading Instruments Co., Ltd.
COF-02 Coefficientof Friction Tester is applicablein static and kinetic coefficient of friction tests of plastic films, sheets,rubber, paper, PP woven bags, fabric style, metal-plastic composite strips/belts for communication cable, conveyor belts, wood, coatings, brakepads, windshield wipers, shoe materials and tyres, etc. With the materialsmoothness testing, users can control and adjust material quality technicalindexes to meet application demands. Besides, this tester is applicable for thesmoothness measurement of cosmetics, eye drop and other daily chemistry.
-
balticFuelCells GmbH
continuously variable contact pressure ensures complete reproducibility of the test conditions ● independent of the thickness of the fuel cell components due to the self-adjusting piston and special sealing concept ● no connection and disconnection of hose- or cable connections for the exchange of cellFixture necessary ● fast &Easy clamping of the cellFixture without tools and precise exchange of the internal cell components ● maximum power density by determining the optimal contact pressure on the active cell surface ● developed for high stress in the field of quality assurance and laboratory environment
-
SKU-015-01-PCIe -
Amfeltec Corp.
PCI Express Backplane was designed to support a variety of modern PCI Express board’s production testing and debugging. The backplane expands the Host computer into four x16 PCI Express slots via 10 ft. CAT7 data and 10-pin flat Power control cables. PCI Express Backplane and UUTs (unit under test – add-in PCI Express board) are powered by a standard ATX power supply connected to the backplane via 24 and 8 pin power connectors located on the backplane.
-
KH23101 -
Beijing KeHuan Century EMC Technology Co,.LTD
The KH23101 current caliper is a toroidal transformer used to measure EMI current. When measuring, the caliper does not directly touch the electrical conductor or the cable under test. The conductor passing through the caliper window is used as the single-turn primary wire of the transformer, and the secondary is designed to be multi-turn. Use with 50 Ω receiving system (such as EMI electromagnetic interference field strength meter or spectrum analyzer). In order to facilitate installation and rapid measurement of EMI current, it is designed as a caliper that can be opened.
-
7630 -
Peaceful Thriving Enterprise Co Ltd
The tester is to connect with the 12V 13-pin Euro-type socket. It can also connect with 7 pin socket through a 13-7 pin towing adaptor. The cable is long enough for user to do the test while sitting in the vehicle. The tester can also do self-test (not work for 7 pin socket), 12V power check, ignition and reversing light. Not available for Newer car with LED light. CAUTION: The self-test is not available with 13-7 pin towing adapter because there is no continuous feed via the 7-pin socket.
-
MDTT9107 -
Matco Tools
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
AmpConnect™ ISC -
Listen Inc
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
Huihong Fiber Inc
Fiber identifier is an essential installation and maintenance instrument which can identify the optical fiber by detecting the optical signals transmitted through them,during this process the fiber optic identifier generate no harm or damage to the fiber cable and it do not need opening the fiber at the splice point for identification or interrupting the service.This fiber identifier detects frequency tones at 270Hz, 1KHZ, 2KHZ, when traffic is present on the fiber under test, an audible tone can be heard. In the meantime, it can identify the traffic direction that indicated by LED with illumination.
-
Extech 380926 -
Extech Instruments Corporation
The 380926 is a category IV, 2000-Amp, TRMS AC/DC Clamp Meter which has a rugged 2 in. jaw that accommodates two 500MCM cables. A built-in full-function DMM can measure AC/DC Voltage and Current, Resistance, capacitance, frequency, Duty Cycle, Diode and Continuity. Measurements are displayed on the large 4000 count backlit display for easy viewing in dimly lit areas. Additional features include DCA push button zero, Data Hold, and Relative function. Complete with test leads and 9V battery.
-
Mirae Corporation
High-quality connection solutions for precise measuring, testing and examination. Whether low or medium voltage range, whether precise test runs or preventive measuring and testing: With an extensive portfolio of specific components and cables, Stäubli always ensures perfect and reliable contact between the measuring instrument and the points, objects and systems to be tested. In addition, we are a proven partner of leading manufacturers of measuring instruments in this field, for example for equipping them with high-quality sockets. Every product meets all quality and safety standards.
-
Oersted Meter -
Alpha Lab, Inc.
The Air Shipment Milligauss Meter has been designed so that one person alone can be the tester, and do repackaging, if necessary, without moving from the area. The remote sensor, shown on the right side, is connected through a 15-foot cable to the control box (left). This control box is placed next to both the package and the tester (person) so the tester can manually rotate the shipment. The remote sensor is placed either 15 feet or 7 feet away, depending on which test is being done.
-
FE44S -
Rohde & Schwarz GmbH & Co. KG
The R&S®FE44S external frontend can extend the frequency range up to 44 GHz for Rohde&Schwarz signal and spectrum analyzers as well as signal generators. The R&S®FE44S enables signal up and downconversion directly at the device under test (DUT), lowering cable losses, increasing sensitivity and delivering more power at the antenna in an OTA environment. The R&S®FE44S uses a single RF connector to further reduce the number of antennas in over the air testing.
-
34939A -
Keysight Technologies
The Keysight 34939A is a high density general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 64 independent single-pole, single-throw (SPST) relays that can switch 1A and carry 2A. This module can be used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The relays are 100V, 1A contacts and can handle up to 60W. Standard 78-pin Dsub connectors allow for use with standard cables, screw terminal blocks, or mass interconnect solutions.
